I got this step error:

8:02 PM
[CLEAR_NOZZLE_QUICK] end_pos[2]:2.9989062500000028
8:02 PM
[CLEAR_NOZZLE_QUICK] src_pos[2]:3.1710085227272966
8:01 PM
Run Current: 0.56A Hold Current: 0.56A
8:01 PM
y_park = 104.5
8:01 PM
x_park = -104.5
8:01 PM
x_axes: xyz
8:01 PM
x_axes: xyz
8:01 PM
wait temp end
8:01 PM
File selected
8:01 PM
File opened:3DBenchy.gcode Size:3135094
7:58 PM
{'code': 'key526', 'msg': 'PR_ERR_CODE_HAVE_LOST_STEP: Z-axis motor step loss was found.', 'values': ['RUN_G29_Z check last point res_z:(0.8845624999999828) out of lost_step_dis:0.5']}
7:58 PM
{'code': 'key526', 'msg': 'PR_ERR_CODE_HAVE_LOST_STEP: Z-axis motor step loss was found.', 'values': ['RUN_G29_Z check last point res_z:(0.8845624999999828) out of lost_step_dis:0.5']}
7:58 PM
{'code': 'key526', 'msg': 'PR_ERR_CODE_HAVE_LOST_STEP: Z-axis motor step loss was found.', 'values': ['RUN_G29_Z check last point res_z:(0.8845624999999828) out of lost_step_dis:0.5']}
7:58 PM
[RAISE_ERROR]{'code': 'key526', 'msg': 'PR_ERR_CODE_HAVE_LOST_STEP: Z-axis motor step loss was found.', 'values': ['RUN_G29_Z check last point res_z:(0.8845624999999828) out of lost_step_dis:0.5']}
7:58 PM
probe at 109.999,125.498 is z=-0.076000
7:58 PM
probe at 79.999,125.498 is z=-0.025832
7:58 PM
probe at 80.000,109.998 is z=0.058594
7:58 PM
probe at 110.000,109.998 is z=-0.017341
7:58 PM
probe at 140.000,109.998 is z=-0.085937
7:58 PM
probe at 140.000,94.498 is z=2.954417
7:57 PM
probe at 109.999,94.498 is z=3.106459
7:57 PM
probe at 79.999,94.498 is z=3.140000
7:57 PM
8 | (140.0, 125.5) | (140.0, 125.5)
7:57 PM
7 | (110.0, 125.5) | (110.0, 125.5)
7:57 PM
6 | (80.0, 125.5) | (80.0, 125.5)
7:57 PM
5 | (80.0, 110.0) | (80.0, 110.0)
7:57 PM
4 | (110.0, 110.0) | (110.0, 110.0)
7:57 PM
3 | (140.0, 110.0) | (140.0, 110.0)
7:57 PM
2 | (140.0, 94.5) | (140.0, 94.5)
7:57 PM
1 | (110.0, 94.5) | (110.0, 94.5)
7:57 PM
0 | (80.0, 94.5) | (80.0, 94.5)
7:57 PM
bed_mesh: generated points
Index | Tool Adjusted | Probe
7:57 PM
Generating new points...
7:57 PM
KAMP adjustments successful. Happy KAMPing!
7:57 PM
Adapted mesh bounds: 79.9995,94.498, 140.0,125.502
7:57 PM
Fuzz amount is 0, mesh points not fuzzed.
7:57 PM
Mesh margin is 0, margin not increased.
7:57 PM
Default mesh bounds: 5.0,5.0, 215.0,215.0
7:57 PM
Adapted probe count: 3,3
7:57 PM
Default probe count: 5,5
7:57 PM
Algorithm: lagrange
7:57 PM
Starting Adaptive Bed Mesh...
7:55 PM
[CLEAR_NOZZLE_QUICK] end_pos[2]:2.9731250000000014
7:55 PM
[CLEAR_NOZZLE_QUICK] src_pos[2]:3.134999999999998
7:55 PM
Run Current: 0.56A Hold Current: 0.56A
7:54 PM
y_park = 104.5
7:54 PM
x_park = -104.5
7:53 PM
x_axes: xyz
7:53 PM
x_axes: xyz
7:53 PM
wait temp end
7:53 PM
File selected
7:53 PM
File opened:3DBenchy.gcode Size:3135094
7:49 PM
{"code":"key111", "msg": "Extrude below minimum temp
7:49 PM
{"code":"key111", "msg": "Extrude below minimum temp
See the 'min_extrude_temp' config option for details", "values": []}
7:48 PM
y_park = 104.5
7:48 PM
x_park = -104.5
7:47 PM
x_axes: xyz
7:47 PM
x_axes: xyz
7:47 PM
File selected
7:47 PM
File opened:CE6_TST-PROGBASE_Rev. A2.gcode Size:764883
7:46 PM
SET_HEATER_TEMPERATURE HEATER=extruder TARGET=210
7:46 PM
SET_HEATER_TEMPERATURE HEATER=extruder TARGET=220
7:40 PM
{"code":"key111", "msg": "Extrude below minimum temp
7:40 PM
{"code":"key111", "msg": "Extrude below minimum temp
See the 'min_extrude_temp' config option for details", "values": []}
7:38 PM
y_park = 104.5
7:38 PM
x_park = -104.5
7:38 PM
move xy
7:38 PM
x_axes is NULL
7:35 PM
File selected
7:35 PM
File opened:CE6_TST-PROGBASE_Rev. A2.gcode Size:764883
7:35 PM
SDCARD_PRINT_FILE FILENAME="CE6_TST-PROGBASE_Rev. A2.gcode"